Ever since we moved into our townhouse, we’ve been slowly adding to our furniture collection. One of the biggest necessities has been more storage space. In the living room, we’ve been just piling nicely folding blankets and leaving them out on the couch. It works, but we were ready for a more organized space. So I decided to make the blankets their very own home – the DIY storage chest.
Finally a place for all that fluffy blanket goodness!
If you’re looking for a quick-build storage solution, follow along below and download the plans & materials here.
This post contains affiliate links. See my full disclosure policy for more information.
TOOLS & SUPPLIES:
- Tape Measure
- Safety Glasses
- Hearing Protection
- Kreg Jig
- 1-1/4” PH Screws
- Wood Filler
- Finish Nailer
- Miter Saw
- Circular Saw
- Orbital Sander
Line up the side pieces to sit flush on all edges with the outside edges of the base. Attach the sides of the bench to the base with 1-1/4” pocket hole screws and wood glue.
Position the front and back of the bench between the side pieces and flush with the outside edge of the base.
Attach to the sides and base with 1-1/4” pocket hole screws and wood glue.
Line up the trim so that it is flush with the top and bottom of the chest in order to hide the plywood edges. As seen on the cut list, I cut my trim with 45° mitered edges. Make sure the front and side trim pieces line up flush at those corner joints for a nice finished edge.
I already have all the trim on in this picture, but it shows that corner joint pretty clearly:
Attach the top and bottom trim to the chest with finish nails and wood glue.
I used a hammer, finish nails, and a nail setter since I don’t have a nailer right now (next on the list though!). A finishing nailer would go quicker, but use whatever you have available!
Position and attach the front upright trim pieces according to the dimensions shown on the plans. Set the upright trim so that it is flush with the edges of your top and bottom trim. Again, use finish nails and wood glue.
Looking from the back of the chest, the upright trim should overhang the edges 1/4” if it is flush with the top and bottom trim.
They’ve been in the last couple photos, but, after completing this build, I would choose to add the furniture feet now (after trim) rather than earlier. It’s not a deal-breaker situation, just a hindsight’s-20/20-preference (I just made that up … ).
Most feet come with bolts for easy attachment. Simply pre-drill the holes according to the bolt size and screw into place. I used some wood glue on the top of the feet before screwing into place to ensure a good hold.
Yes … that’s a case of Coors in the background … cus this is a classy-ass garage that I’m working in … i.e. the couch saga.
Lastly, make the lid for the storage chest. I made my lid by attaching 1x4s and 1x6s with 1-1/4” pocket hole screws and wood glue from the bottom side of the lid to best hide the pocket holes.
As you can see, the lid boards were not totally flush when I first put them together since I was building with simple, rough-cut lumber. It took some elbow grease and sanding to make an even surface, but it was worth it!
Once I had the storage box and lid built, I filled all holes and plywood edges with wood filler, let it dry, and then finished with sanding. I went over everything with 120 grit and then followed up with 220 grit, which left a nice baby-butt-smooth surface 🙂
Finally, paint or stain as desired! I used Glidden ‘Antique White’ for the chest and Minwax ‘Special Walnut’ for the lid.
And, last but not least, attach the storage chest lid with hinges at the back of the chest. I just used basic hinges from the Home Depot.
Let me know if you have any questions.
And if you build from this plan, please share! I’d love to see it!
I’ve shared this project over at Remodelaholic for their Friday Favorites link up. Head over to see all the great ideas this week!