DIY Mobile Workbench with Table Saw & Miter Saw

Build a DIY mobile workbench that fits both your table saw and miter saw with these plans.

DIY Mobile Workbench with Table Saw & Miter Saw

This post may contain affiliate links. If you make a purchase from one of the links, I may make a small commission at NO EXTRA COST to you. This helps keep the tutorials and plans free here at Bitterroot DIY. Thank you for your support! See my full disclosure here.

You all loved the DIY Mobile Workbench with Table Saw so much that I brought it back for round #2! I teamed up with my friend Ashley from Shes the Carpenter over on Instagram for this NEW & IMPROVED mobile workbench with BOTH a table saw and miter saw. If you don’t already, make sure to go follow Ashley for TONS of amazing DIY projects! She built this beast of a workbench and is always sharing great woodworking tips and tricks!

There are two variations of plans – one for a RIGID table saw (pictured) and the other for a RYOBI table saw.

I featured the dimensions for the RIGID table saw in the post below, but you can adjust the table saw shelf to fit any table saw. The only thing you have to change is the size of the shelf and location of the support leg that the shelf attaches to.

Enjoy the plans!

**If you find any errors in the plans, please let me know and I’ll update them accordingly. I do my best to get everything correct, but it’s just me back here behind the screen checking my own work.

The lumber and cut lists are available for purchase. Your purchase also includes a downloadable PDF of the plans. If you prefer, the plans are available for free in the post below – you simply have to calculate the lumber and cut lists yourself. There are plans available to fit a RYOBI table saw, as well as a RIGID table saw. If you own a different table saw, you can just adjust the shelf to fit.

Step 1.

Assemble the bottom frame according to the diagram. Use 2 1/2″ self tapping screws through the frame to attach the 2x4s. Pocket holes are a great option if you don’t want to see the screws from the front of the bench. However, since this is just a workbench, I simply screwed through the frame into the shorter 2x4s.

DIY workbench step 1

Step 2.

Attach the side legs to the bottom frame with 2 1/2″ screws. The bottom of the frame should sit flush with the bottom of the legs.

DIY workbench step 2

Step 3.

Attach the front and back legs to the frame and side legs with 2 1/2″ screws. I attached the legs to the frame first and then drove a couple screws through the legs into the narrow side of the front and back legs to secure them together. You can see the approximate location of the screws in the diagram above.

DIY workbench step 3

The diagram only shows dimensions on the front legs. The back legs exactly mirror it.

Here’s a top view of how the legs go together:

DIY workbench step 4

Step 4.

Put the bottom shelf in place on the bottom frame and attach with 1 1/4″ screws. Countersink the screws so they won’t get in the way. It’s very difficult to put the bottom shelf in later, so definitely put it in before attaching the top frame in Step 5.

DIY workbench step 5

Step 5.

Build the top frame in place as shown. Use 2 1/2″ screws to attach the frame to the legs.

Here’s a different view from the front to show you what it looks like at this point:

DIY workbench step 7

Step 6.

Attach the 2×4 feet to the legs with 2 1/2″ screws. Fasten the locking casters to the feet with 1 1/4″ screws. I used washers on each screw since the screw heads were smaller than the holes in the caster wheels. You could also use washer head screws.

DIY workbench step 8

Step 7.

Assemble the frame for the table saw shelf with 2 1/2″ screws. Place those two center 2×4 supports wherever necessary to support the base of your table saw.

DIY workbench step 9

You could also add particle board on top of the 2×4 frame to set the table saw on. Just make sure to leave room in the bottom for dust collection (or at least for the sawdust to fall out).

Step 8.

Place the shelf at the appropriate height for your table saw and attach to the workbench frame with 2 1/2″ screws. Use clamps to hold the shelf in place while you attach it to the frame.

DIY workbench step 10

Side View:

DIY workbench step 11

Step 9.

Measure the height of your miter saw’s tabletop. A good way to do this is to set your saw on a flat surface, lay a board across the saw so it extends off the edge, and measure from the flat surface to the bottom of the board.

Position the 2×4 miter saw shelf supports at the appropriate height so the top of the miter saw will sit flush with the tabletop when it’s on the shelf.

Attach the 2×4 miter saw shelf supports to the inside of the midSlide the miter saw shelf particleboard into place on top of the 2x4s you just attached.dle legs. Drive two 2 1/2″ screws on each side into the legs.

DIY workbench step 12

Slide the miter saw shelf particleboard into place on top of the 2x4s you just attached.

DIY workbench step 13

Step 10.

Attach a stop block on each side behind the miter saw shelf to prevent the shelf from sliding backward under the bench.

You can just use an extra piece of 2×4 cut to fit and attach it to the 2×3 and 2×4 shelf support.

DIY workbench step 14

Step 11.

Center the tabletop and attach it to the frame with 1 1/4″ screws. There should be a 2″ overhang on the sides of the table top and it should be flush with the outside edge of the legs along front and back. Countersink the screws into the particle board so they won’t get in the way of your work.

DIY workbench step 15

Step 12.

Since the miter saw shelf is just held in place by the stop blocks you attached in Step 11, you can use that same piece of particle board (or plywood) to fill in the tabletop when you need the full workbench.

Place the miter saw shelf in the shelf slot when you want to use the saw:

DIY workbench step 16

Move the shelf up to the top of the workbench when you need a full out-feed table:

DIY workbench step 17

Step 13.

**Optional: Add a small clamp rack along the end of the workbench once it’s finished. On the first DIY mobile workbench, I just used a small scrap board and screwed it to the inside of the legs.

DIY workbench step 18

Ashley added the clamp rack in a little different spot, so feel free to do whatever works best for your shop.

She also added a small nightstand along the far side of the workbench for some extra drawer storage, which is such a great use of space:

DIY Mobile Workbench with Table Saw & Miter Saw

And just for good measure, here are a few more photos to show how that miter saw shelf works:

DIY Mobile Workbench with Table Saw & Miter Saw
DIY Mobile Workbench with Table Saw & Miter Saw

Good luck, happy building, and don’t forget to tag me @bitterrootdiy and Ashley @shesthecarpenter over on Instagram if you build this ULTIMATE DIY Mobile Workbench! We’d love to see it! You can also send me photos at [email protected]

Please let me know if you have any questions and I’ll get back to you as soon as possible.

Bitterroot DIY

Thanks for stopping by!

For more project ideas, you can find me on Pinterest. And to stay up to date with the latest shenanigans, follow me on Instagram.

DIY Mobile Workbench with Table Saw & Miter Saw

Reader Interactions


  1. Alejandro says

    Good morning,

    I have no experience in woodworking, but I am trying to learn. I got the pans for this table and was just wondering, at what point do you add the wheels? I did the bottom part and it is gettingheavy.

    Thank you

    • tylynn_sattler says

      Hi there,

      I added the wheels once I got the bottom frame assembled. I just flipped it on it’s side to attach them. It’s a bit of a beast haha but I think that’s the best time to do it.

  2. Coe says

    Hello, the picture looks like plywood for the tops vs particle board in the description. Do you prefer one over the other?

    • tylynn_sattler says

      Both your comments went through, so I answered on the other one. Hope that’s helpful!

  3. Coe says

    I apologize if this posts twice, I had an error and wasn’t sure if the first post went through.
    I was just getting your opinion on plywood tops vs particle board? It looks like the pictures above have plywood tops but your description mentioned particle board. Of course one of the big difference being price but other than that what do you think?

    • tylynn_sattler says

      Hi there!

      I like to use particle board for workbenches, but this project was a collaboration with another gal who built it and she used plywood. I usually use particleboard since it’s a little cheaper and just going on a workbench. Totally up to you.

    • tylynn_sattler says

      I don’t have the exact model number (will make a note to get that next time), but you can measure your saw and check it against the plans to see if it fits. You can see the diagrams with dimensions for the plans if you scroll down the post, so you don’t have to purchase to check your measurements if it doesn’t work.

  4. Bill Burks says

    I paid for the plans and cuts – since I felt that $2.99 was reasonable for your efforts! however, one critical dimension is missing – that is the dimension from the end of the table top to the start of the 2-9″ mitre saw opening cut on the plywood.
    I calculate it to be 22-1/4″, is this right? You need to know exactly where to start that cut.

    • tylynn_sattler says

      Hi Bill, thanks for purchasing the plans and letting me know that I missed that dimension. I’ll update the plans with it. I believe your calculation is correct and it should start at 22 1/4″.

  5. Richard D says

    The workbench is just what I was looking to build. Thanks for the plans. Would it make sense to leave a overhang on the front and back of the table for more clamping spots.

    • tylynn_sattler says

      You can leave more of an overhang if you want. I have limited space and was trying to maximize shelf size vs tabletop size. Totally up to you though

  6. johnny mitchell says

    Hey again. I found the plans in my download folder on my computer. YEAH! I just could not bring them up from your website.

  7. Mike Bell says

    I’ve only done a few projects, so I’m definitely a newbie at woodworking. I’ve been looking for plans like this workbench, so I’m glad I stumbled across your page!
    I started building the work today, so I’m taking my time getting it done because I want this workbench to last! Now I just have to hide the credit card statement where my wife doesn’t see how much I spent, lol!!

    • tylynn_sattler says

      3″ locking casters – they’re linked at the top of the plans under TOOLS & SUPPLIES, or you can find them at Home Depot.

  8. Chet says

    I bought the plan and made this table over this past weekend And it turned out great, just wanted to say thanks! The plans were very well done and easy to follow, really happy with how it turned out and can’t wait to put this puppy to use!

  9. Justin says


    i have a 8 1/4 dewalt table saw which plan would i use for that?

    also what is the lenght and width or the work bench when its completed?

    • tylynn_sattler says

      I’m not sure the dimensions on the DeWalt – You’ll have to adjust the tablesaw frame a little bit to fit it. Either plan will work since you have to make that adjustment. The finished tabletop is 4’x8′.

  10. Andrew says

    Any issues with dust collection under the table saw? I’d hate to store anything under it and get it all dusty. Any suggestions? Trying to figure out my dust collection issue.

    • tylynn_sattler says

      I put a bucket under there and it catches quite a bit. I’ve seen people do a bucket with a shop vac attached too and that seems to work pretty well.

  11. rob says

    it looks as if you have cut the tabletop out of one sheet of plywood…are those dimensions included somewhere? or is it another case of something being right in front of my face and i just dont see it? lol please let me know…i have not purchased the plans yet but have no problem doing so…maybe those dimensions are in the cut list?


    • tylynn_sattler says

      I put those dimensions in the cut diagram if you purchase the plans. If you prefer not to purchase the plans, you can always just cut the plywood to fit your saws.

      Thanks and good luck with the project!


  12. Andrew Wright says


    I bought the plans and printed them out for use. However I noticed the “Tools & Supplies” wasn’t in the pdf I downloaded, so when I went to shop for supplies I couldn’t use the printout. I suggest adding that list up front in the PDF so the whole project is included in the document, preventing others from using both this web page and the downloaded plans to assemble the workbench.

    • tylynn_sattler says

      Thanks for your suggestions. I order a lot of the materials online so I like to link to the exact products.

  13. Riley Nemeth says

    Working on the table now…. easy to follow and straightforward. One problem I am running into is that my table saw (Dewalt) has a track on the front and the back, so I will have to route or cut out room for it so I can still use the track/fence on the table saw….

    • tylynn_sattler says

      I’m glad the plans are easy to follow! I’ve had a few other people build it for different tablesaws and they routed out a space for the fence also – hope that works out and you get lots of good use out of it!

    • tylynn_sattler says

      Haha I’m 5’1″, so I hear ya! I built it that height so I didn’t have to bend over for sanding 😉

  14. Jesse says

    Hello! I am a complete newbie and love the plans. My question is about the height of the saws. Should the table top be flush with the saws or no? Also you give a tip on how to measure for the miter saw would it be the same for the table saw?

    • tylynn_sattler says

      The tabletop should be flush with the table top of the table saw, as well as the tabletop of the miter saw. The shelf for the miter saw has to be a little lower than the tabletop so the tabletop of the miter saw ends up flush (so you can run a board across it to cut).

  15. Matthias says

    Hi there,

    This work table looks great!
    I’m wondering what program you use to design this on?

    Many thanks!

  16. Steve Daniell says

    Tylynn this is my second build from your collection. I’m not new to this, but you have had some really cool ideas. I built your miter saw station with the flip up extensions and loved it. Just finished this table and really like it a lot. I added a flip top miter station and a router table at the far end. Going to add T Track in a couple of locations, but hats off, great plans and better ideas!

    • tylynn_sattler says

      Hi Steve,

      Thanks so much! Those are great additions to this one. I hope you get tons of good use out of both workbenches!

  17. Devin says

    Hey Tylynn I made this a love it .changed up some stuff but very easy to work with what you have to Follow.i was wondering what Software you used to make your print.

    Thanks Devin

    • tylynn_sattler says

      That’s great to hear! I hope you get tons of good use out of it. I use SketchUp to draw all my plans. There’s a free online version if you’re interested in trying it out.

  18. Jimmy says

    Hi, I need to modify the plans for Metabo saw and miter, plus I want to add a router station. Could I get the sketch plans so I can tweak it? I bought the plans but only got the PDF.

    • tylynn_sattler says

      Unfortunately, I don’t give cost estimates since prices fluctuate so much depending on location. Lumber prices are also up right now due to COVID.

  19. Guy Johnson says

    This is a great work bench. Built it this week over 3 evenings.
    I have a 7 1/4″ mitre saw, so had to make feet for my saw to get it over the 3″ self, works great.
    Very clear instructions and sketches.