DIY Coffee Table with Truss Sides

Free woodworking plans to build a DIY coffee table.

DIY Modern Farmhouse Coffee Table

This post contains affiliate links. If you make a purchase from one of the links, I may make a small commission at NO EXTRA COST to you. This helps keep the tutorials and plans free here at Bitterroot DIY. Thank you for your support! See my full disclosure here.

This project was actually a bit nostalgic – the very first piece of furniture that I built was a DIY coffee table. I made SO many mistakes and had to redo things over and over until I got it right. But, let me tell ya, it was worth the hassle. Who knew that 3 years later I’d be writing my own plans. I guess you never really know what you’re getting yourself into when you start something new!

This coffee table is pretty similar to that first one I built (original plans from Ana White), but I changed up the dimensions and style a little.

Enjoy the plans!

Tools & Supplies

Lumber

  • 2 | 2 x 6 @ 8′
  • 2 | 2 x 4 @ 8′
  • 2 | 2 x 2 @ 8′
  • 2 | 1 x 4 @ 8′
  • 1 | 3/4″ x 1/2″ Trim Stop (available in the trim aisle OR you can cut it out of a 1x board with a table-saw or circular saw)

Cuts

  • 4 | 2 x 4 @ 17″ (legs)
  • 4 | 2 x 4 @ 17″ (side frame)
  • 4 | 2 x 2 @ 24 1/2″ (front & back frame)
  • 4 | 2 x 2 @ 14 3/8″ with 25 degree parallel miter (side truss)
  • 2 | 3/4″ x 1/2″ Trim @ 24 1/2″ (bottom shelf cleat)
  • 6 | 1 x 4 @ 17″ (bottom shelf)
  • 4 | 2 x 6 @ 35 1/2″ (tabletop)

Step 1.

Attach the 2×4 frame boards to the legs as shown with wood glue and 2 1/2″ pocket holes. For the top 2x4s – place the pocket holes on the top side so the tabletop will hide them. For the bottom 2x4s – place the pocket holes on the bottom so you won’t be able to see them easily. Use two pocket holes on each end of the 2x4s for a secure joint with the legs.

DIY Coffee Table step 1

Build two frames.

DIY Coffee Table step 1b

Step 2.

Join the side frames together with the 2×2 frame boards. Align the top 2x2s flush with the top of the legs, and position the bottom 2x2s 1″ from the bottom of the legs (as shown in the diagram).

DIY Coffee Table step 2

Use wood glue and 2 1/2″ pocket hole screws. Again, place pocket holes on the top of the top 2x2s and the bottom of the bottom 2x2s to best hide them. Use two pocket holes on each end of the boards.

Step 3.

Attach the 2×2 truss boards to the side frame with wood glue and 2″ finish nails. Center the 2x2s along the 2×4 frame. Position the 2x2s with the bottom of the boards tight against the inside of the legs + bottom 2×4 and the top tight against the top 2×4. This will leave a small gap between 2x2s along the top of the frame.

DIY Coffee Table step 3

If your cuts aren’t perfect for the truss boards, it’s not a big deal. Just move them around until they’re tight in the frame. The gap at the top doesn’t have to be any specific measurement.

Do one 2×2 at a time – apply wood glue on the ends, then put the 2×2 in place. Once you like how it fits, hold the 2×2 in place while you drive 2″ finish nails through the 2×4 frame into the 2×2. Make sure to drive the nails at a slight angle so they don’t go through the other side of the 2×2, but keep your hands clear just in case a nail goes through. Drive two finish nails into each end.

**If you don’t own a finish nailer – you can just drive screws through the frame into the 2x2s.

Repeat for both sides.

DIY Coffee Table step 3b

Step 4.

Time for the bottom shelf cleats. I used a 1/2″ x 3/4″ trim stop from Menards:

DIY Coffee Table cleat

If you can’t find a trim stop, you can always cut one from a 1x board with a table saw or circular saw. If you don’t own a table saw or circular saw, consider attaching the slats with pocket holes (see the alternative method explained below, just before step 5).

Attach 3/4″ x 1/2″ cleats to the inside of both of the bottom 2×2 frame boards with wood glue and 1 1/4″ screws. I used three screws for each cleat (one on either end and one in the middle).

Position the cleats with the 3/4″ side against the 2x2s and the 1/2″ side facing upwards. The actual dimensions of a 2×2 is 1 1/2″, so align the 3/4″ cleat with the bottom of the 2x2s to leave 3/4″ for the 1×4 slats (1 1/2″ – 3/4″ = 3/4″).

DIY Coffee Table step 4

Space the bottom shelf slats 1/2″ apart and attach them to the cleats with 1 1/4″ finish nails.

DIY Coffee Table step 5

**Alternative Method: If you prefer, you can attach the 1×4 slats with pocket holes. Drill the pocket holes along the bottom of each 1×4, line them up with the top of the 2×2 frame and attach with wood glue 1 1/4″ pocket hole screws.

**Handy Tip: I recommend sanding and staining the 1×4 slats before attaching them so you don’t have to try to reach between each one. It’s much easier.

Step 5.

To build the table top, stagger pocket holes along the 2x6s and join them together with wood glue and 2 1/2″ pocket hole screws. Face three pocket holes one way and two the opposite way for a solid joint all the way down the boards.

Like so:

DIY Coffee Table step 7

Once you’ve built the tabletop, center it over the coffee table frame and attach it.

DIY Coffee Table step 6

I simply drove 2 1/2″ screws through the bottom of the 2x2s into the tabletop to attach it. Feel free to use whatever method you prefer.

Step 6.

Sand and stain as desired!

DIY Modern Farmhouse Coffee Table

I stained this coffee table with Varathane Dark Walnut and sealed it with Varathane glossy water-based polyurethane (both available at Home Depot).

Please let me know if you have any questions and I’ll get back to you as soon as possible.

Bitterroot DIY

Thanks for stopping by!

For more project ideas, you can find me on Pinterest. And to stay up to date with the latest shenanigans, follow me on Instagram.

DIY Modern Farmhouse Coffee Table

Reader Interactions

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.